ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Akizragore Arashikasa
Country: Zimbabwe
Language: English (Spanish)
Genre: Sex
Published (Last): 9 November 2015
Pages: 138
PDF File Size: 6.66 Mb
ePub File Size: 9.27 Mb
ISBN: 862-8-99948-274-3
Downloads: 68655
Price: Free* [*Free Regsitration Required]
Uploader: Gokazahn

F When approved by the purchaser, alloys or Se may be furnished. A Tensile stress areas are computed using the following formula: It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. A – Machined from annealed or solution annealed f5944 thus retaining the properties of the original material; or hot formed and solution annealed.

Unless otherwise specified, all bolts, hex cap screws, r594 studs used with these nuts shall conform to the requirements of Specification F and shall be of the same alloy group. ASTM does not give any asmt express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

ASTM f Nuts|ASTM F Specification | Nuts Fasteners| Get a Live Quote Now for ASTM f Nuts

Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties.

  JURNAL PENDERAAN FIZIKAL KANAK-KANAK PDF

CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. SH – Machined from strain hardened stock or cold worked to develop the specific properties.

Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

D Yield strength is the stress at which an offset of 0. Condition CW – When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and then cold worked to develop the specified properties.

Historical Version s – view previous versions of standard.

Free Technical Information

C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread g594 determined in accordance with Test Methods F E When approved by the purchaser, alloy F may be furnished.

The finished fasteners shall meet the applicable mechanical properties.

F59 Minimum values except where shown as maximum or as a range. Link to Active This link will always route to the current Active version of the standard.

  JURNAL INFEKSI NOSOKOMIAL PDF

This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has been completed.

ASTM F Specification – Boltport Fasteners LLP

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. B legend of conditions: Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed.

ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

This abstract is a brief summary of the referenced standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.